Browse categories

East-West Guitars 

Quality Replacement Parts

Member since:
17/04/2015
Last online:
13/12/2018
Location:
Rathfarnham, Dublin

Activity

Active:
204
Sold out:
28
Withdrawn:
89
Units sold:
833

Feedback Score [283]

  • Oak Styled 5-Way Lever Switch, "Super Switch", Four Pole

    3 5-way 4-pole, double wafer switch with stainless steel screws. An economical alternative to the Oak Grigsby super switch made to the exact same specifications for a fraction of the price. Very similar in construction to the Oak Grigsby switches and have the same lever feel. Wire your guitar in new and imaginative ways, use for coil splitting, coil tap, series/parallel wiring or conventional, phase reversal etc. All the above can be carried out with this switch and more if combined with mini toggle switches, push/pull pots. Specifications: Body cavity depth required 1-3/8" (34.93mm) Mounting screw spacing 1-5/8" (41.28mm) Lever stem .050" x .190" (1.27mm x 4.82mm) Pickguard slot required 1/16" x 1-1/16" (1.59mm x 26.99mm) (for the lever)

    €15.95
  • Oak Grigsby 5-Way Lever Switch For Fender Stratocaster

    3 Genuine Oak Grigsby 5-Way lever switch for Fender Stratocaster and Telecaster Exact Replacement for Fender 5-way lever switch for Stratocaster. Used on USA Modern Fender Strats and vintage Strats. -Fits Fender & Fender style Strats and other guitars (some modification of the pickguard on Far Eastern Strat copies may be required check the spacing requirements below) -Fits 1/16 in. x 1-1/16 in. slot. 1-5/8 in. center to center screw spacing. 1-3/8 in. cavity -Single wafer configuration - 4 pole, 5 way lever switch. -Mounting screws included (Switch Tip NOT included) *Only tips for 'USA' switches will work with this switch. Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Combined postage on all listings in my shop is available from East-West Guitars. However, until Adverts get around to offering the customer and the seller a shopping cart so the seller can calculate the shipping for the customer for multiple items the only solution is as follows. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately**

    €11.95
  • Oak Grigsby 4-Way Lever Switch For Telecaster Mod

    3 4-Way Lever Switch made by Oak Grigsby Exact Replacement for Fender 4-way lever switch for Telecaster. -Fits Fender & Fender style Telecasters and other guitars -Mounting screws included (Switch Tip NOT included) The 4-way Tele switch modification will give you both sounds when you dial in the two pickups together - wired in parallel (standard wiring) and wired in series for a beefier fuller sound. Switch Positions: 1. Bridge 2. Bridge & Neck in Parallel 3. Neck 4. Bridge & Neck in Series (Humbucker Type Fullness)

    €14.95
  • Oak Grigsby 5-Way Lever Switch, Double Pole

    3 This Oak Grigsby switch by Electroswitch lets you wire guitars in imaginative ways not possible with a standard 5-way switch. It's a special 2-pole switch with six lugs per pole (one common and one each for the five lever positions. The added terminals allow a level of flexibility and control that is not possible with traditional lever switches. Terminal assignment: There are a total of 12 solder terminals (lugs) on this switch. The switch is divided into two separate circuits, or poles, and each pole has six lugs. Lug 0 is the common which is connected to other lugs depending on the lever's position. The five other terminals on each pole correspond to the five positions of the switch. Lug #1 = position 1, Lug #2 = position 2, etc. Many lever switches use the commons as outputs for the switch, but with this switch this is not necessarily going to be the case. The commons of this switch can be used to connect pickups together in ways not possible with other switches. This is an important concept to understand when designing custom wiring for this switch. Specs and Dimensions: Oak single wafer - 2 pole, 5 way lever switch Standard U.S. size. Fits 5/8 in. x 1-1/16 in. slot. 1-5/8 in. center to center screw spacing. 1-3/8 in. cavity depth. Mounting screws included Feel free to ask questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Postage on this item is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Combined postage on all listings in my shop is available from East-West Guitars. However, until Adverts get around to offering the customer and the seller a shopping cart so the seller can calculate the shipping for the customer for multiple items the only solution is as follows. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately depending on final weight of package**

    €18.50
  • Nitrocellulose Lacquer, Aerosol Can, 500 ml (Options available)

    3 Nitrocellulose lacquer has been used on guitars since the fifties and sixties because of its excellent characteristics. Forming a very thin layer it allows the wood to resonate freely with little restraint. It can be spot repaired easily and when buffed, shows a beautiful shine. Finally, the way this lacquer ages (cracking, yellowing, checking) adds to the character of the instrument. 500 ml per can Colours available: Black Gloss Vintage White Olympic White Old Fiesta Red Daphne Blue Sonic Blue Lake Placid Blue (Metallic) Sherwood Green (Metallic) Clear coat high gloss (final layer) Tinted clear coat (neck amber/vintage finish) Primer, white (light finishes) Primer, grey (for dark finishes) Primer, transparent (for see-through finishes) Sunburst Heart Yellow (center finish for LP) Tobacco Brown (perfect for honeyburst) Sunburst Red (perfect for 3 tone transition) Postage is at the standard rate for one can, if you want your items sent by registered post please send me a message. If buying multiple cans please inquire for postage and lead time as I don't have all the colours in stock.

    €18.95
  • Quilter Labs Overdrive 200, 200W 4 Channel, Amplifier Head

    3 Quilter Labs first multi channel "Block Style" amplifier. The Overdrive 200: is inspired by legendary and almost unobtainable amplifiers, bringing an iconic overdrive sound within reach of the average musician. The dynamic 200 watt Quilter Tone Block power section is combined with a traditional Tone Stack EQ section to form a classic clean channel, along with multiple switchable drive sections providing several explosive overdriven tones. Versatile & Compact: For the first time we managed to house four distinct tones in our popular Block style enclosure. Clean Channel: The big brother to our 101 Reverb. Tone Stack EQ section married with an active Mid control for a wide range of high headroom clean tone. Crunch Channel: A preset Mid Scoop is engaged for a tight mid-gain tone. EQ controls are defeated and the Drive Channels Gain and Output are activated so desired saturation and volume balance can be easily achieved. Lead Channel: The Lead Channel shares the EQ setting with the Clean Channel so to not have a dramatic shift in tone between voicings. The gain structure is based on rare and collectable early cascading gain stage amplifiers. The Gain and Output controls also become active and is balanced with Crunch Channel. Bonus: Lead + Crunch Engaging both the Lead and Crunch channel delivers the high gain tone of the Lead Channel and removes the EQ from the circuit for an unrefined heavy tone. Footswitch: The Overdrive 200 accepts a standard two position footswitch with or without LEDs. In the interest of saving you money we have decided to not offer a Quilter branded footswitch. Generic footswitches are widely available at music stores around the world. We have included an adhesive label with every Overdrive 200 so that you can label your own. Specifications: 200 watts of power 4 to 8 Ohms Two Channels, 4 modes Clean channel: Gain & Output Dirt channel: Gain, Bass, Mid, Treble, & Master controls 1/4" high impedance input jack Effects Loop: 1/4" Send and Return jacks 1/4" Headphone jack for quiet practice Dual 1/4" speaker outputs for variable loads 16 to 4 ohms Locking IEC power cable Universal power supply automatically works anywhere in the world Ultra compact (roughly the size of a double wide effects pedal) 3.15" (80mm) x 8.5" (216mm) x 5.8" (147mm) 4 Pounds (1.8kg) Warranty Information: Customers may have additional rights, which vary from state to state or from country to country. In the event that a provision of this limited warranty is void, prohibited or superseded by local laws, the remaining provisions shall remain in effect. The Quilter Labs limited warranty is valid for a period of three (3) years from date of purchase except that footswitches, covers, cabinets, handles, and cabinet hardware are warranted for a period of one (1) year and speakers, and all other included accessory products for a period of ninety (90) days from date of purchase. All accessories (Footswitches, controllers, deluxe cases) are warranted for a period of 90 days from date of purchase. Defective products that qualify for coverage under this warranty will be repaired or replaced, (at Quilter Labs' discretion) with a like or comparable product, without charge. To receive warranty service, return the complete product to Quilter Labs, LLC, with proof of purchase, during the applicable warranty period. The Quilter Labs Dealer from whom you purchased your product may also be authorized for warranty service and should be the first point of contact when service is required. TRANSPORTATION COSTS ARE NOT INCLUDED IN THIS LIMITED WARRANTY. Any repair or service performed by any person or entity other than an Authorized Quilter Labs Electronics Service Center is not covered by this limited warranty. The long awaited solution for bass players is here! Built from the Ground up: Built specifically for the bass guitar, the Bass Block 800 represents the culmination of years of research and development. Unlike many of today's compact bass amps, the Bass Block 800 is not simply an existing consumer-grade power module married to a pre-amp, but a comprehensive power system that responds dynamically and musically to the players instrument and touch. Ultra-Light, Ultra-Strong: The Bass Block is so light you might forget you are carrying it to the gig! Using an ultralight aluminum chassis, internal fan-cooled heat sink, and ferreting out every ounce possible, the Bass Block manages to pack 800 watts into a sturdy and insanely lightweight 4-lb package. Real world power at any voltage: Using high power technology developed for world-class pro audio touring, the Bass Block 800 delivers effortless reserves of power to maintain tight control of the speaker without clipping or bottoming out. The universal-voltage power supply delivers smooth and powerful response regardless of club voltage surges. The amp works on any voltage, anywhere. Plug it in, turn it up, enjoy the effortless beauty of the tone! The most "musical" bass head ever? Pat Quilters first amp was built in 1967 for his brothers bass player, and great bass tone remains a key passion. The modern bass is a full-range instrument, with much different dynamic requirements than electric guitar. Low frequencies require more horsepower to move air, and the instrument demands percussive response without bottoming out or obtrusive limiting. The Bass Block provides 800 real watts to build on, and the preamp is optimized to make the best use of that power, providing more effective headroom with less stress on the speakers. Unique bass-specific EQ controls allow the bassist to quickly dial in a wide range of tones to match any instrument, and a special 2-stage limiter prevents bottoming out without suppressing dynamic response and feel. A Master control allows the peak power point to be adjusted to safely power any size of speaker, from giant stacks down to compact studio units. A prolonged field testing program has confirmed that every component in the Bass Block 800 is focused on creating the ultimate musical instrument for bass players. You will feel it every moment of every gig. Effortless, powerful, and exacting tone at your fingertips. The ultimate tool in your arsenal. Specifications: Power Output: 225 watts-16 Ohms, 450 watts-8 ohms, 800-watts, 4 ohms (2 Ohm use possible, but may experience clipping at high volume.) AC Power Req.: 100240Vac, 5060 Hz, 250 W typical, 1000W peak. Signal Connections: PASSIVE INPUT: " mono (full gain), 2 meg ACTIVE INPUT: " mono (-10dB gain), 30K LINE INPUT: XLR 10K balanced, 1V full scale. LINE OUTPUT: XLR, quasi-balanced, 400 ohms, 1V full scale Controls: GAIN CONTROL MUTE BUTTON (with red warning LED) DEPTH CONTROL (100Hz Hi-Q bass control) CONTOUR CONTROL (Low-mid scoop, flat, treble cut) MASTER CONTROL (adjusts peak power from 0 to 800W) PILOT LIGHT (winks if the amplifier is driven into thermal limiting) Speaker Connections: 4-8 ohms, 90V, 25A peak Dual jacks, 8 ohms each Speakon (2 wire) 4-8 ohms. Headphone Out: 3.5mm mini-jack, 20 ohms per side, 2V peak. Dimensions: H x W x D 8.5(218mm) x 7.5 (190mm) x 3 (76mm) Weight: 3.7 lbs (2kg) Approvals: UL recognized, tested to conform to FCC/CE limits for Class B devices. *Power cable shipped with Type G or Type F plug Need more specs? Click here for the manual http://quilterlabs.s3-us-west-1.amazonaws.com/2013site/manuals/2100-bass_block_800.pdf A word on the technology behind the Bass Block 800 from Pat Quilter http://www.quilterlabs.com/index.php/products/bassblock-amplifiers/bass-block-in-depth Demos: https://www.youtube.com/watch?v=i4MSt9hRqbo https://www.youtube.com/watch?v=MEnJweAouaE Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Quilter Labs Warranty Information: Customers may have additional rights, which vary from state to state or from country to country. In the event that a provision of this limited warranty is void, prohibited or superseded by local laws, the remaining provisions shall remain in effect. The Quilter Labs limited warranty is valid for a period of three (3) years from date of purchase except that footswitches, covers, cabinets, handles, and cabinet hardware are warranted for a period of one (1) year and speakers, and all other included accessory products for a period of ninety (90) days from date of purchase. All accessories (Footswitches, controllers, deluxe cases) are warranted for a period of 90 days from date of purchase. Defective products that qualify for coverage under this warranty will be repaired or replaced, (at Quilter Labs' discretion) with a like or comparable product, without charge. To receive warranty service, return the complete product to Quilter Labs, LLC, with proof of purchase, during the applicable warranty period. The Quilter Labs Dealer from whom you purchased your product may also be authorized for warranty service and should be the first point of contact when service is required. TRANSPORTATION COSTS ARE NOT INCLUDED IN THIS LIMITED WARRANTY. Any repair or service performed by any person or entity other than an Authorized Quilter Labs Electronics Service Center is not covered by this limited warranty. ***IMPORTANT INFORMATION*** A CUSTOMS CHARGES OF 25 APPLIES TO THE FOLLOWING COUNTRIES. PLEASE SEND ME A MESSAGE FIRST BEFORE PURCHASING IF YOU RESIDE IN: Bosnia-Herzegovina Iceland Liechtenstein Norway Serbia & Montenegro Switzerland Tunisia Turkey ***If purchasing it would be a good idea to send me a message first as to what country you reside in as prices for shipping to different countries in Europe vary. Inquire first to get the best price for shipping.***

    Guitar Amps
    6 months ago 11 comments
    €450
  • Quilter Labs 101 Mini Head, 50-100W

    3 **Authorized Quilter Labs Amplification Dealer** An incredibly potent amplifier so light, it feels like an empty box. 50 watts of power and an enormous tone shaping capability and weighing only two pounds! The first amplifier range to combine powerful, ultralight Class-D power technology and superb analog tone processing, to capture the warmth and feel of the best classic amplifiers less the weight and hassle of antiquated vacuum tubes. The Quilter 101 Mini Head: Imagine being able to pack 5 of history's greatest sounding amplifiers into a package so small it fits in the pouch of your gig bag. Imagine a head so light you almost forgot it was there. Imagine a streamlined set up that only takes a few moments. Forget about the problems you are used to, like bad voltage or tiny stages. Plug it in and turn it up. Your friends stop snickering and their jaws begin to drop as a generous helping of Quilter wattage fills the room. Now they are asking where to get theirs. Welcome to a whole new world of practical and affordable tone. Lightweight: Your back has been waiting for this since the first time you laid hands on a heavy amp. With the 101 Mini Head, you can have gloriously huge tone without lugging around bulky and temperamental heads. On the stage: Real world power that sounds even bigger than tube technology. Unlike last-generation solid state technologies, Quilter amplifiers have enormous internal headroom far above our published rated power. This means you get extra voltage swing, huge transients and, more importantly, the feel and harmonic content you can't usually get without glowing bottles. At home: Turn the Master way down, or plug in your headphones and keep it totally quiet as you work on your music late into the evening. The 101 Mini Head is the perfect missing link between your effects and your speaker cab, and tucks in anywhere to make your DAW look even more beautiful. Get one: Backed by a industry-leading warranty, Quilter amplifiers are setting new standards in performance amplification. Your new Quilter 101 will be far more reliable than any traditional technology and is backed by a team with a passion for music and a commitment to ensuring you get the most from your tone -- every gig, every song, every time. Specifications: 50 watts of FullQ power with up to 100 watts on the "clean" settings (Jazz and Surf) Gain, Tri-Q, Voicing, Hi-Cut and Master controls 1/4" high impedance input jack Effects Loop: 1/4" Send and Return jacks 1/8" Headphone jack for quiet practice Dual 1/4" speaker outputs for variable loads 16 to 4 ohms Standard IEC power cable (non locking) Universal power supply -- take it anywhere in the world without need for transformers or switches Ultra compact (roughly the size of a double wide effects pedal) 8 3/8"W x 3 1/8"H x 5 1/2"D Weight: 2 Pounds Choice of UK or European power cable Warranty Information: Customers may have additional rights, which vary from state to state or from country to country. In the event that a provision of this limited warranty is void, prohibited or superseded by local laws, the remaining provisions shall remain in effect. The Quilter Labs limited warranty is valid for a period of three (3) years from date of purchase except that footswitches, covers, cabinets, handles, and cabinet hardware are warranted for a period of one (1) year and speakers, and all other included accessory products for a period of ninety (90) days from date of purchase. All accessories (Footswitches, controllers, deluxe cases) are warranted for a period of 90 days from date of purchase. Defective products that qualify for coverage under this warranty will be repaired or replaced, (at Quilter Labs' discretion) with a like or comparable product, without charge. To receive warranty service, return the complete product to Quilter Labs, LLC, with proof of purchase, during the applicable warranty period. The Quilter Labs Dealer from whom you purchased your product may also be authorized for warranty service and should be the first point of contact when service is required. TRANSPORTATION COSTS ARE NOT INCLUDED IN THIS LIMITED WARRANTY. Any repair or service performed by any person or entity other than an Authorized Quilter Labs Electronics Service Center is not covered by this limited warranty.

    Guitar Amps
    6 months ago 17 comments
    €295
  • Quilter Labs Micro Block 45, Pedal Sized Amplifier

    3 PEDAL SIZED POWER AMP Quilters in-depth knowledge of tone and overdrive is now available in a compact pedal format with 33/45 watts of speaker power. Perfect for the player who doesnt need the mighty Tone Blocks 200-watt output. Go ahead, plug in, turn it up & watch the jaws drop as a big helping of high energy Quilter mojo pours out of this little box! Clean or dirty, this efficient little workhorse keeps on rocking. INTUITIVE CONTROLS Gain, Tri-Q, Master. The same three wide-range controls that made the Tone Block 200 famous are now available in pedal form. Gain goes from clean to soaring overdrive. Tri-Q goes from Blackface chime to roaring lead boost. And Master takes you from full output down to zero with no change in tone or overdrive. Perfect for practice or playing out. AMAZING FLEXIBILITY As a complete miniature guitar amp, the MicroBlock 45 can fill a bedroom, living room, or even a small club as a backup amp. In addition, the MicroBlock makes a great utility amp for driving headphones, and a great general purpose playback amp using either the guitar or mini-jack input. It can even be used as a natural distortion pedal by using the headphone jack as a line output. Its the easiest way to see what the Quilter thing is all about. FEATURES Comes with universal voltage 72-watt power supply Quarter-inch high impedance input for maximum pickup response Quarter inch speaker output drives 16, 8 and 4 ohm loads, and is fully protected Mini-jack input accepts stereo inputs, summing to mono Mini-jack output drives headphones or line outputs (you can run this straight into the line level input on a mixing console from a 3.5 mm adapter) Power cable shipped with Type G or Type F plug Mystery gift included Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Quilter Labs Warranty Information: Customers may have additional rights, which vary from state to state or from country to country. In the event that a provision of this limited warranty is void, prohibited or superseded by local laws, the remaining provisions shall remain in effect. The Quilter Labs limited warranty is valid for a period of three (3) years from date of purchase except that footswitches, covers, cabinets, handles, and cabinet hardware are warranted for a period of one (1) year and speakers, and all other included accessory products for a period of ninety (90) days from date of purchase. All accessories (Footswitches, controllers, deluxe cases) are warranted for a period of 90 days from date of purchase. Defective products that qualify for coverage under this warranty will be repaired or replaced, (at Quilter Labs' discretion) with a like or comparable product, without charge. To receive warranty service, return the complete product to Quilter Labs, LLC, with proof of purchase, during the applicable warranty period. The Quilter Labs Dealer from whom you purchased your product may also be authorized for warranty service and should be the first point of contact when service is required. TRANSPORTATION COSTS ARE NOT INCLUDED IN THIS LIMITED WARRANTY. Any repair or service performed by any person or entity other than an Authorized Quilter Labs Electronics Service Center is not covered by this limited warranty. Demos: https://www.youtube.com/watch?v=ekjpRuQONeA https://www.youtube.com/watch?v=8ZfxFHuivuY https://www.youtube.com/watch?v=FwUS_D68UBo

    Guitar Amps
    6 months ago 6 comments
    €150
  • Quilter Labs 101 Reverb, 50W Amplifier Head

    3 The Quilter 101 Reverb: Featuring an expanded control set with Bass, Mid, and Treble, the 101 steps out from a supporting role for your pedals and into the limelight as a full featured guitar head! With other popular features such as Limiter and FX Loop, the 101 Reverb means serious business. Featuring an interesting new take on the usual three-knob EQ section, the Bass and Treble controls use traditional tone stack technology, yielding a familiar bright chime based on 50 years of tradition, while the active Mid control provides a more strongly voiced cut/boost function for increased versatility. Increasing the Mid control boosts the frequencies that give an aggressive D-Style bite to the sound, while decreasing Mid brings out that familiar clean-60s Blackface tone. Lightweight: Weighing the same 2 pounds as its little brother, the 101 Reverb is so light you'll think we forgot to put the guts in! Even with the same compact footprint, it has more than enough power to bring any cabinet to life! On the stage: The 101 Reverb carries forward all the tone and power you've come to expect, while forging new sonic territory. Unlike last-generation solid state technologies, Quilter amplifiers have enormous internal headroom far above our published rated power. This means you get extra voltage swing, huge transients, and more importantly, the feel and harmonic content that usually requires glowing bottles. At home: Turn the Master way down, or plug in your headphones and keep it totally quiet, as you work on your music late into the evening. The 101 Reverb is the perfect missing link between your effects and your speaker cab. Get one: Backed by a industry-leading warranty, Quilter amplifiers are setting new standards in performance amplification. Your new Quilter 101 will be far more reliable than any traditional technology. Our support is backed by a team with a passion for music and a commitment to ensuring you get the most from your tone every gig, every song, every time. Specifications: 50 watts of FullQ power Gain, Limiter, Bass, Mid, Treble, Reverb, & Master controls 1/4" high impedance input jack Effects Loop: 1/4" Send and Return jacks 1/4" Headphone jack for quiet practice Dual 1/4" speaker outputs for variable loads 16 to 4 ohms Standard IEC power cable (non locking) Universal power supply automatically works anywhere in the world Ultra compact (roughly the size of a double wide effects pedal) 8 3/8"W x 3 1/8"H x 5 1/2"D (21.3cm W x 7.9cm H x 14cm D) 2 Pounds (0.9kg) Warranty Information: Customers may have additional rights, which vary from state to state or from country to country. In the event that a provision of this limited warranty is void, prohibited or superseded by local laws, the remaining provisions shall remain in effect. The Quilter Labs limited warranty is valid for a period of three (3) years from date of purchase except that footswitches, covers, cabinets, handles, and cabinet hardware are warranted for a period of one (1) year and speakers, and all other included accessory products for a period of ninety (90) days from date of purchase. All accessories (Footswitches, controllers, deluxe cases) are warranted for a period of 90 days from date of purchase. Defective products that qualify for coverage under this warranty will be repaired or replaced, (at Quilter Labs' discretion) with a like or comparable product, without charge. To receive warranty service, return the complete product to Quilter Labs, LLC, with proof of purchase, during the applicable warranty period. The Quilter Labs Dealer from whom you purchased your product may also be authorized for warranty service and should be the first point of contact when service is required. TRANSPORTATION COSTS ARE NOT INCLUDED IN THIS LIMITED WARRANTY. Any repair or service performed by any person or entity other than an Authorized Quilter Labs Electronics Service Center is not covered by this limited warranty. The long awaited solution for bass players is here! Built from the Ground up: Built specifically for the bass guitar, the Bass Block 800 represents the culmination of years of research and development. Unlike many of today's compact bass amps, the Bass Block 800 is not simply an existing consumer-grade power module married to a pre-amp, but a comprehensive power system that responds dynamically and musically to the players instrument and touch. Ultra-Light, Ultra-Strong: The Bass Block is so light you might forget you are carrying it to the gig! Using an ultralight aluminum chassis, internal fan-cooled heat sink, and ferreting out every ounce possible, the Bass Block manages to pack 800 watts into a sturdy and insanely lightweight 4-lb package. Real world power at any voltage: Using high power technology developed for world-class pro audio touring, the Bass Block 800 delivers effortless reserves of power to maintain tight control of the speaker without clipping or bottoming out. The universal-voltage power supply delivers smooth and powerful response regardless of club voltage surges. The amp works on any voltage, anywhere. Plug it in, turn it up, enjoy the effortless beauty of the tone! The most "musical" bass head ever? Pat Quilters first amp was built in 1967 for his brothers bass player, and great bass tone remains a key passion. The modern bass is a full-range instrument, with much different dynamic requirements than electric guitar. Low frequencies require more horsepower to move air, and the instrument demands percussive response without bottoming out or obtrusive limiting. The Bass Block provides 800 real watts to build on, and the preamp is optimized to make the best use of that power, providing more effective headroom with less stress on the speakers. Unique bass-specific EQ controls allow the bassist to quickly dial in a wide range of tones to match any instrument, and a special 2-stage limiter prevents bottoming out without suppressing dynamic response and feel. A Master control allows the peak power point to be adjusted to safely power any size of speaker, from giant stacks down to compact studio units. A prolonged field testing program has confirmed that every component in the Bass Block 800 is focused on creating the ultimate musical instrument for bass players. You will feel it every moment of every gig. Effortless, powerful, and exacting tone at your fingertips. The ultimate tool in your arsenal. Specifications: Power Output: 225 watts-16 Ohms, 450 watts-8 ohms, 800-watts, 4 ohms (2 Ohm use possible, but may experience clipping at high volume.) AC Power Req.: 100240Vac, 5060 Hz, 250 W typical, 1000W peak. Signal Connections: PASSIVE INPUT: " mono (full gain), 2 meg ACTIVE INPUT: " mono (-10dB gain), 30K LINE INPUT: XLR 10K balanced, 1V full scale. LINE OUTPUT: XLR, quasi-balanced, 400 ohms, 1V full scale Controls: GAIN CONTROL MUTE BUTTON (with red warning LED) DEPTH CONTROL (100Hz Hi-Q bass control) CONTOUR CONTROL (Low-mid scoop, flat, treble cut) MASTER CONTROL (adjusts peak power from 0 to 800W) PILOT LIGHT (winks if the amplifier is driven into thermal limiting) Speaker Connections: 4-8 ohms, 90V, 25A peak Dual jacks, 8 ohms each Speakon (2 wire) 4-8 ohms. Headphone Out: 3.5mm mini-jack, 20 ohms per side, 2V peak. Dimensions: H x W x D 8.5(218mm) x 7.5 (190mm) x 3 (76mm) Weight: 3.7 lbs (2kg) Approvals: UL recognized, tested to conform to FCC/CE limits for Class B devices. *Power cable shipped with Type G or Type F plug Need more specs? Click here for the manual http://quilterlabs.s3-us-west-1.amazonaws.com/2013site/manuals/2100-bass_block_800.pdf A word on the technology behind the Bass Block 800 from Pat Quilter http://www.quilterlabs.com/index.php/products/bassblock-amplifiers/bass-block-in-depth Demos: https://www.youtube.com/watch?v=i4MSt9hRqbo https://www.youtube.com/watch?v=MEnJweAouaE Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Quilter Labs Warranty Information: Customers may have additional rights, which vary from state to state or from country to country. In the event that a provision of this limited warranty is void, prohibited or superseded by local laws, the remaining provisions shall remain in effect. The Quilter Labs limited warranty is valid for a period of three (3) years from date of purchase except that footswitches, covers, cabinets, handles, and cabinet hardware are warranted for a period of one (1) year and speakers, and all other included accessory products for a period of ninety (90) days from date of purchase. All accessories (Footswitches, controllers, deluxe cases) are warranted for a period of 90 days from date of purchase. Defective products that qualify for coverage under this warranty will be repaired or replaced, (at Quilter Labs' discretion) with a like or comparable product, without charge. To receive warranty service, return the complete product to Quilter Labs, LLC, with proof of purchase, during the applicable warranty period. The Quilter Labs Dealer from whom you purchased your product may also be authorized for warranty service and should be the first point of contact when service is required. TRANSPORTATION COSTS ARE NOT INCLUDED IN THIS LIMITED WARRANTY. Any repair or service performed by any person or entity other than an Authorized Quilter Labs Electronics Service Center is not covered by this limited warranty. ***IMPORTANT INFORMATION*** A CUSTOMS CHARGES OF 25 APPLIES TO THE FOLLOWING COUNTRIES. PLEASE SEND ME A MESSAGE FIRST BEFORE PURCHASING IF YOU RESIDE IN: Bosnia-Herzegovina Iceland Liechtenstein Norway Serbia & Montenegro Switzerland Tunisia Turkey ***If purchasing it would be a good idea to send me a message first as to what country you reside in as prices for shipping to different countries in Europe vary. Inquire first to get the best price for shipping.***

    Guitar Amps
    6 months ago 5 comments
    €385
  • Emerson Custom/CTS 250K Potentiometer Short (3/8") Split Shaft

    3 When quality and tone cannot be compromised, Emerson circuits are the answer. Emerson PRO CTS - 250K Short (3/8") Split Shaft Potentiometer - 1/4" split shaft for fine-knurled (24-spline) US Spec knobs. - Typically used on Strat style guitars with single coil pickups, but can be used on any guitar that requires a 250K Split Shaft Potentiometer. Emerson Pro CTS pots from Emerson Custom are designed to be the premium choice for the discerning guitarist looking for the optimum performance and tonal response from a guitar potentiometer. These specially designed Emerson Pro CTS feature a longer-life brass shaft and bushing. They also feature a tighter 8% resistance tolerance compared to CTS products offered by most other suppliers. Each and every Emerson Pro CTS pot is hand tested to ensure that they meet or exceed our stated tolerances. We take great pride in offering some of the best, most consistent potentiometers on the market today. Emerson Pro CTS pots have a proprietary custom audio taper that was specially designed by Emerson Custom to give you a very smooth and accurate response when you roll up and down on the controls. These pots will give you a much more responsive taper than what you'll get with economy or even standard issue CTS pots. Crank your guitar up to 10 and the volume swells all the wayno abrupt flattening to choke your playing style. Clarity and Precision define this Series of Premium Potentiometers by Emerson Custom. Each Emerson Pro CTS pot includes a flat washer, lock washer, and two hex mounting nuts for custom height adjustment on a pickguard, control plate, or directly on to the guitars top from inside the control cavity. Specifications: Shaft Style: (24 Spline) Split Shaft, Fine Knurling Shaft Material: Long life brass Shaft Diameter: 0.234 (6.00MM) Shaft Height: 3/8 (9.52MM) Thread: 3/8 X 32 Thread Height: 3/8 (9.52MM) Required Mounting Hole: 3/8 (9.52MM) ***THESE ARE NOT METRIC COMPONENTS, SOME REAMING OF THE RECIEVING HOLES MAY BE NEEDED! ALSO, THE KNOBS ON YOUR GUITAR MAY NEED TO BE REPLACED AS THESE POTS ARE THE FINE SPLINED VARIETY AS OPPOSED TO THE COURSE SPLINES ON EUROPEAN GUITARS*** Brand: Emerson/CTS Pro Line Country/Region of Manufacture: United States MPN: 450S3830 1536 Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Combined postage on all listings in my shop is available from East-West Guitars. However, until Adverts get around to offering the customer and the seller a shopping cart so the seller can calculate the shipping for the customer for multiple items the only solution is as follows. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately**

    €7.95
  • Emerson Custom/CTS 500K Potentiometer Short (3/8") Split Shaft

    3 When quality and tone cannot be compromised, Emerson circuits are the answer. Emerson Pro CTS 500K Potentiometer Short (3/8") Split Shaft Audio Taper pot. - 1/4" split shaft for fine-knurled (24-spline) US Spec knobs. - Typically used on SG's, Flat Top Non Carved Top Les Pauls, PRS's, LP Jr's and many other models of guitars, but can be used on any guitar that requires a 500K Split Shaft Potentiometer. Emerson Pro CTS pots from Emerson Custom were designed to be the premium choice for the discerning guitarist looking for the optimum performance and tonal response from a guitar potentiometer. These specially designed Emerson Pro CTS feature a longer-life brass shaft and bushing. They also feature a tighter 8% resistance tolerance compared to CTS products offered by most other suppliers. Each and every Emerson Pro CTS pot is hand tested to ensure that they meet or exceed the stated tolerances listed here. Emerson Pro CTS pots have a proprietary custom audio taper that was specially designed by Emerson Custom to give you a very smooth and accurate response when you roll up and down on the controls. These pots will give you a much more responsive taper than what you'll get with economy or even standard issue CTS pots. Crank your guitar up to 10 and the volume swells all the wayno abrupt flattening to choke your playing style. Clarity and Precision define this Series of Premium Potentiometers by Emerson Custom. Each Emerson Pro CTS pot includes a flat washer, lock washer, and two hex mounting nuts for custom height adjustment on a pickguard, control plate, or directly on to the guitars top from inside the control cavity. Specifications: Shaft Style: (24 Spline) Split Shaft, Fine Knurling Shaft Diameter: 0.234 (6.00MM) Shaft Height: 3/8 (9.52MM) Thread: 3/8 X 32 Thread Height: 3/8 (9.52MM) Required Mounting Hole: 3/8 (9.52MM) ***THESE ARE NOT METRIC COMPONENTS, SOME REAMING OF THE RECIEVING HOLES MAY BE NEEDED! ALSO, THE KNOBS ON YOUR GUITAR MAY NEED TO BE REPLACED AS THESE POTS ARE THE FINE SPLINED VARIETY AS OPPOSED TO THE COURSE SPLINES ON FAR EASTERN GUITARS*** Brand: Emerson/CTS Pro Line Country/Region of Manufacture: United States MPN: 450S3834 1536 Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in original packaging. **Combined postage on all listings in my shop is available from East-West Guitars. However, until Adverts get around to offering the customer and the seller a shopping cart so the seller can calculate the shipping for the customer for multiple items the only solution is as follows. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately**

    €7.95
  • Emerson Custom/CTS 250K Potentiometer Short (3/8") Solid Shaft

    3 When quality and tone cannot be compromised, Emerson circuits are the answer. Emerson Pro CTS 250K Potentiometer Short (3/8") Solid Shaft Audio Taper pot. - 3/8" Solid Shaft for use with (1/4) US Spec set-screw knobs. - Typically used on Tele Style Guitars with Single Coil Pickups Emerson Pro CTS pots from Emerson Custom were designed to be the premium choice for the discerning guitarist looking for the optimum performance and tonal response from a guitar potentiometer. These specially designed Emerson Pro CTS feature a longer-life brass shaft and bushing. They also feature a tighter 8% resistance tolerance compared to CTS products offered by most other suppliers. Each and every Emerson Pro CTS pot is hand tested to ensure that they meet or exceed our stated tolerances. These are some of the best, most consistent potentiometers on the market today. Emerson Pro CTS pots have a proprietary custom audio taper that was specially designed by Emerson Custom to give you a very smooth and accurate response when you roll up and down on the controls. These pots will give you a much more responsive taper than what you'll get with economy or even standard issue CTS pots. Crank your guitar up to 10 and the volume swells all the wayno abrupt flattening to choke your playing style. Clarity and Precision define this Series of Premium Potentiometers by Emerson Custom. Each Emerson Pro CTS pot includes a flat washer, lock washer, and two hex mounting nuts for custom height adjustment on a pickguard, control plate, or directly on to the guitars top from inside the control cavity. Specifications: Shaft Style: ROUND SOLID SHAFT Shaft Diameter: 0.250 (6.35MM) Shaft Height: 3/8 (9.52MM) Thread: 3/8 X 32 Thread Height: 3/8 (9.52MM) Required Mounting Hole: 3/8 (9.52MM) ***THESE ARE NOT METRIC COMPONENTS, SOME REAMING OF THE RECEIVING HOLES MAY BE NEEDED!*** Brand: Emerson/CTS Pro Line Country/Region of Manufacture: United States MPN: 450S3831 1502 Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Combined postage on all listings in my shop is available from East-West Guitars. However, until Adverts get around to offering the customer and the seller a shopping cart so the seller can calculate the shipping for the customer for multiple items the only solution is as follows. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately**

    €7.95
  • Emerson Custom/CTS 500K Potentiometer Short (3/8") Solid Shaft

    3 When quality and tone cannot be compromised, Emerson circuits are the answer. Emerson Pro CTS 500K Potentiometer Short (3/8") Solid Shaft Audio Taper pot. - 3/8" Solid Shaft for use with (1/4) US Spec set-screw knobs. - Typically used on Tele Style Guitars with Humbucker or P90 Pickups, but can be used on any guitar that requires a 500K Solid Shaft Potentiometer. Emerson Pro CTS pots from Emerson Custom were designed to be the premium choice for the discerning guitarist looking for the optimum performance and tonal response from a guitar potentiometer. These specially designed Emerson Pro CTS feature a longer-life brass shaft and bushing. They also feature a tighter 8% resistance tolerance compared to CTS products offered by most other suppliers. Each and every Emerson Pro CTS pot is hand tested to ensure that they meet or exceed our stated tolerances. We take great pride in offering some of the best, most consistent potentiometers on the market today. Emerson Pro CTS pots have a proprietary custom audio taper that was specially designed by Emerson Custom to give you a very smooth and accurate response when you roll up and down on the controls. These pots will give you a much more responsive taper than what you'll get with economy or even standard issue CTS pots. Crank your guitar up to 10 and the volume swells all the wayno abrupt flattening to choke your playing style. Clarity and Precision define this Series of Premium Potentiometers by Emerson Custom. Each Emerson Pro CTS pot includes a flat washer, lock washer, and two hex mounting nuts for custom height adjustment on a pickguard, control plate, or directly on to the guitars top from inside the control cavity. Specifications: Shaft Style: ROUND SOLID SHAFT Shaft Diameter: 0.250 (6.35MM) Shaft Height: 3/8 (9.52MM) Thread: 3/8 X 32 Thread Height: 3/8 (9.52MM) Required Mounting Hole: 3/8 (9.52MM) ***THESE ARE NOT METRIC COMPONENTS, SOME REAMING OF THE RECEIVING HOLES MAY BE NEEDED!*** More than 10 available. Brand: Emerson/CTS Pro Line Country/Region of Manufacture: United States MPN: 450S3832 1432 Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Combined postage on all listings in my shop is available from East-West Guitars. However, until Adverts get around to offering the customer and the seller a shopping cart so the seller can calculate the shipping for the customer for multiple items the only solution is as follows. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately**

    €7.95
  • Emerson Custom/CTS 500K Potentiometer Long (3/8") Split Shaft

    3 When quality and tone cannot be compromised, Emerson circuits are the answer. Emerson PRO CTS - 500K Long (3/4") Split Shaft Potentiometer - 1/4" split shaft for fine-knurled (24-spline) US Spec knobs. - Typically used on Carved Top Les Pauls, but can be used on any guitar that requires a 500K Long Split Shaft Potentiometer. Emerson Pro CTS pots from Emerson Custom were designed to be the premium choice for the discerning guitarist looking for the optimum performance and tonal response from a guitar potentiometer. These specially designed Emerson Pro CTS feature a longer-life brass shaft and bushing. They also feature a tighter 8% resistance tolerance compared to CTS products offered by most other suppliers. Each and every Emerson Pro CTS pot is hand tested to ensure that they meet or exceed their stated tolerances. They take great pride in offering some of the best, most consistent potentiometers on the market today. Emerson Pro CTS pots have a proprietary custom audio taper that was specially designed by Emerson Custom to give you a very smooth and accurate response when you roll up and down on the controls. These pots will give you a much more responsive taper than what you'll get with economy or even standard issue CTS pots. Crank your guitar up to 10 and the volume swells all the wayno abrupt flattening to choke your playing style. Clarity and Precision define this Series of Premium Potentiometers by Emerson Custom. Each Emerson Pro CTS pot includes a flat washer, lock washer, and two hex mounting nuts for custom height adjustment on a pickguard, control plate, or directly on to the guitars top from inside the control cavity. Specifications: Shaft Style: (24 Spline) Split Shaft, Fine Knurling Shaft Diameter: 0.234 (6.00MM) Shaft Height: 3/8 (9.52MM) Thread: 3/8 X 32 Thread Height: 3/4 (19.05MM) Required Mounting Hole: 3/8 (9.52MM) ***THESE ARE NOT METRIC COMPONENTS, SOME REAMING OF THE RECIEVING HOLES MAY BE NEEDED! ALSO, THE KNOBS ON YOUR GUITAR MAY NEED TO BE REPLACED AS THESE POTS ARE THE FINE SPLINED VARIETY AS OPPOSED TO THE COURSE SPLINES ON FAR EASTERN GUITARS*** Brand: Emerson/CTS Pro Line Country/Region of Manufacture: United States MPN: 450S3833 1504 Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Combined postage on all listings in my shop is available from East-West Guitars although Adverts does not seem to have this function unlike Ebay. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately**

    €9.95
  • Emerson Custom/CTS 1 Meg Ohm, Short (3/8") Split Shaft Potentiometer

    3 When quality and tone cannot be compromised, Emerson circuits are the answer. Emerson PRO CTS - 1 Mega Ohm Short (3/8") Split Shaft Audio Potentiometer - 1/4" split shaft for fine-knurled (24-spline) US Spec knobs. - Typically used on Fender Style guitars with single coil pickups (i.e.: Jazzmasters, Jaguars, etc) but can be used on any guitar that requires a 1 Meg Split Shaft Potentiometer. Emerson Pro CTS pots from Emerson Custom were designed to be the premium choice for the discerning guitarist looking for the optimum performance and tonal response from a guitar potentiometer. These specially designed Emerson Pro CTS feature a longer-life brass shaft and bushing. Emerson Pro CTS pots have a proprietary custom audio taper that was specially designed by Emerson Custom to give you a very smooth and accurate response when you roll up and down on the controls. These pots will give you a much more responsive taper than what you'll get with economy or even standard issue CTS pots. Crank your guitar up to 10 and the volume swells all the wayno abrupt flattening to choke your playing style. Clarity and Precision define this Series of Premium Potentiometers by Emerson Custom. Each Emerson Pro CTS pot includes a flat washer, lock washer, and two hex mounting nuts for custom height adjustment on a pickguard, control plate, or directly on to the guitars top from inside the control cavity. Specifications: Shaft Style: (24 Spline) Split Shaft, Fine Knurling Shaft Diameter: 0.234 (6.00MM) Shaft Height: 3/8 (9.52MM) Thread: 3/8 X 32 Thread Height: 3/8 (9.52MM) Required Mounting Hole: 3/8 (9.52MM) ***THESE ARE NOT METRIC COMPONENTS, SOME REAMING OF THE RECIEVING HOLES MAY BE NEEDED! ALSO, THE KNOBS ON YOUR GUITAR MAY NEED TO BE REPLACED AS THESE POTS ARE THE FINE SPLINED VARIETY AS OPPOSED TO THE COURSE SPLINES ON EUROPEAN GUITARS*** Brand: Emerson/CTS Pro Line Country/Region of Manufacture: United States MPN: 450S3888 1510 Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Combined postage on all listings in my shop is available from East-West Guitars although Adverts does not seem to have this function unlike Ebay. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately** .

    €7.95
  • Emerson Custom/CTS 1 Meg Ohm, Short (3/8") Solid Shaft Potentiometer

    3 When quality and tone cannot be compromised, Emerson circuits are the answer. Emerson PRO CTS - 1 Mega Ohm Short (3/8") Solid Shaft Potentiometer - 3/8" Solid Shaft for use with (1/4) US Spec set-screw knobs. - Typically used on Fender Style Guitars with Single Coil Pickups (i.e.: Jazzmasters, Jaguars, etc) - 10% Tolerance - Custom Designed Audio Taper - Brass shaft and bushing - 3/8" Shaft for Mounting on Pickguards, Control Plates or flat top guitars (Includes a flat washer, lock washer, and two hex mounting nuts for custom height adjustment) Emerson Pro CTS pots from Emerson Custom were designed to be the premium choice for the discerning guitarist looking for the optimum performance and tonal response from a guitar potentiometer. These specially designed Emerson Pro CTS feature a longer-life brass shaft and bushing. Emerson Pro CTS pots have a proprietary custom audio taper that was specially designed by Emerson Custom to give you a very smooth and accurate response when you roll up and down on the controls. These pots will give you a much more responsive taper than what you'll get with economy or even standard issue CTS pots. Crank your guitar up to 10 and the volume swells all the wayno abrupt flattening to choke your playing style. Clarity and Precision define this Series of Premium Potentiometers by Emerson Custom. Each Emerson Pro CTS pot includes a flat washer, lock washer, and two hex mounting nuts for custom height adjustment on a pickguard, control plate, or directly on to the guitars top from inside the control cavity. Specifications: Shaft Style: ROUND SOLID SHAFT Shaft Diameter: 0.250 (6.35MM) Shaft Height: 3/8 (9.52MM) Thread: 3/8 X 32 Thread Height: 3/8 (9.52MM) Required Mounting Hole: 3/8 (9.52MM) ***THESE ARE NOT METRIC COMPONENTS, SOME REAMING OF THE RECIEVING HOLES MAY BE NEEDED! ALSO, THE KNOBS ON YOUR GUITAR MAY NEED TO BE REPLACED AS THESE POTS ARE THE FINE SPLINED VARIETY AS OPPOSED TO THE COURSE SPLINES ON EUROPEAN GUITARS*** Brand: Emerson/CTS Pro Line Country/Region of Manufacture: United States MPN: 450S3887 1510 Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Combined postage on all listings in my shop is available from East-West Guitars. However, until Adverts get around to offering the customer and the seller a shopping cart so the seller can calculate the shipping for the customer for multiple items the only solution is as follows. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately**

    €7.95
  • Emerson Custom/CTS 250K Blender Potentiometer Short (3/8") Split Shaft

    3 When quality and tone cannot be compromised, Emerson circuits are the answer. 250K BLENDER Potentiometer Short (3/8") Split Shaft. Emerson/CTS PRO AUDIO TAPER Similar in function to the Fender "No Load" pot, the Emerson Pro Blender pot is an improvement to this design idea. This pot acts as a true bypass when rotated between 9 and 10. The main difference from the "No Load" is that the Emerson Pro Blender pot does NOT have a detent, which means a no click feel between 9 and 10. This Blender pot is best used for true bypass tone control or Blender guitar wiring. Has a specially designed custom taper so the "blending" is seamless and very intuitive. - 10% Tolerance - Custom Designed Audio Taper - Brass shaft and bushing - 3/8" Shaft for Mounting on Pickguards, Control Plates or flat top guitars (Includes a flat washer, lock washer, and two hex mounting nuts for custom height adjustment) Emerson Pro CTS pots from Emerson Custom were designed to be the premium choice for the discerning guitarist looking for the optimum performance and tonal response from a guitar potentiometer. These specially designed Emerson Pro CTS feature a longer-life brass shaft and bushing. Emerson Pro CTS pots have a proprietary custom audio taper that was specially designed by Emerson Custom to give you a very smooth and accurate response when you roll up and down on the controls. These pots will give you a much more responsive taper than what you'll get with economy or even standard issue CTS pots. Crank your guitar up to 10 and the volume swells all the wayno abrupt flattening to choke your playing style. Clarity and Precision define this Series of Premium Potentiometers by Emerson Custom. Each Emerson Pro CTS pot includes a flat washer, lock washer, and two hex mounting nuts for custom height adjustment on a pickguard, control plate, or directly on to the guitars top from inside the control cavity. SWITCH & BLENDER POT FUNCTION IN STRATOCASTER WITH 5-WAY SWITCH: Blender Pot on 10: Position 1: Bridge Position 2: Bridge & Middle Position 3: Middle Position 4: Middle & Neck Position 5: Neck Blender Pot on 1: Position 1: Bridge w/ Neck Pickup Faded in Position 2: Bridge & Middle w/ Neck Pickup Faded in Position 3: Middle Position 4: Middle & Neck w/ Bridge pickup Faded in Position 5: Neck w/ Bridge Pickup Faded in ***THESE ARE NOT METRIC COMPONENTS, SOME REAMING OF THE RECIEVING HOLES MAY BE NEEDED! ALSO, THE KNOBS ON YOUR GUITAR MAY NEED TO BE REPLACED AS THESE POTS ARE THE FINE SPLINED VARIETY AS OPPOSED TO THE COURSE SPLINES ON EUROPEAN GUITARS*** Brand: Emerson/CTS Pro Line Country/Region of Manufacture: United States MPN: 450S3845 1436 Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Combined postage on all listings in my shop is available from East-West Guitars. However, until Adverts get around to offering the customer and the seller a shopping cart so the seller can calculate the shipping for the customer for multiple items the only solution is as follows. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately**

    €8.95
  • Fender, No-Load Potentiometer, 250K, Solid Shaft

    3 Genuine Fender 250K ohm, Split Shaft, no load potentiometer. Some Fender guitars have a unique tone circuit that features a "Delta Tone' Control. The "Delta Tone' system consists of a high output bridge pickup and special 'no-load' tone control for the middle and bridge pickups. This new pot has a detent at the 10 position which bypasses completely any filtration through capacitors. Unlike the TBX, which [has] a detent at the 5 position and gradually reduce[s] the amount of filtration through the capacitor, the Delta-Tone's 'no-load' feature eliminates filtration completely at the detent and the result is more of the direct presence of the pickup. Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Must be returned in an unused state and in the original packaging Shipping: I offer a choice between Standard or Registered shipping on all my items. I suggest to choose registered mail for your own protection of items being shipped otherwise use standard mail but at your own risk, choose the standard rate if you would like to save on shipping cost. But please be sure that mail never goes missing.

    €10.95
  • CTS 250K Left Handed Potentiometer. Reverse Audio Logarithmic. Split Shaft

    3 This pot will allow you to wire your guitar up the correct way if you are a left handed player. Potentiometers on left handed guitars usually can only be operated in an anti-clockwise fashion which is a nightmare for some players or with a reverse wiring with a standard pot with the wires simply reversed which is not correct at all as it will reverse the resistance taper. This pot is the answer and will allow the player to engage the control in a clockwise manner when turning it up. From Allparts USA Specifications: Resistance: 250k Ohms Tolerance: +/-10% Shaft Material:Aluminum Pot casing: Dimpled back Shaft Style: (24 Spline) Split Shaft, Fine Knurling Shaft Diameter: 0.234 (6.00MM) Shaft Height: 3/8 (9.52MM) Thread: 3/8 X 32 Thread Height: 3/8 (9.52MM) Required Mounting Hole: 3/8 (9.52MM) ***THESE ARE NOT METRIC COMPONENTS, SOME REAMING OF THE RECIEVING HOLES MAY BE NEEDED! ALSO, THE KNOBS ON YOUR GUITAR MAY NEED TO BE REPLACED AS THESE POTS ARE THE FINE SPLINED VARIETY AS OPPOSED TO THE COURSE SPLINES ON EUROPEAN GUITARS*** Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Combined postage on all listings in my shop is available from East-West Guitars. However, until Adverts get around to offering the customer and the seller a shopping cart so the seller can calculate the shipping for the customer for multiple items the only solution is as follows. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately**

    €8.95
  • CTS 500K Left Handed Potentiometer. Reverse Audio Logarithmic. Split Shaft

    3 This pot will allow you to wire your guitar up the correct way if you are a left handed player. Potentiometers on left handed guitars usually can only be operated in an anti-clockwise fashion which is a nightmare for some players or with a reverse wiring with a standard pot with the wires simply reversed which is not correct at all as it will reverse the resistance taper. This pot is the answer and will allow the player to engage the control in a clockwise manner when turning it up. From Allparts USA Specifications: Resistance: 500K Ohms Tolerance: +/-10% Shaft Material:Aluminum Pot casing: Flat back Shaft Style: (24 Spline) Split Shaft, Fine Knurling Shaft Diameter: 0.234 (6.00MM) Shaft Height: 3/8 (9.52MM) Thread: 3/8 X 32 Thread Height: 3/8 (9.52MM) Required Mounting Hole: 3/8 (9.52MM) ***THESE ARE NOT METRIC COMPONENTS, SOME REAMING OF THE RECIEVING HOLES MAY BE NEEDED! ALSO, THE KNOBS ON YOUR GUITAR MAY NEED TO BE REPLACED AS THESE POTS ARE THE FINE SPLINED VARIETY AS OPPOSED TO THE COURSE SPLINES ON EUROPEAN GUITARS*** Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Combined postage on all listings in my shop is available from East-West Guitars. However, until Adverts get around to offering the customer and the seller a shopping cart so the seller can calculate the shipping for the customer for multiple items the only solution is as follows. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately**

    €8.95
  • Bourns Dual MN Taper Balance/Blend Pot, With Center Detent (Various types)

    3 Choose between split shaft or solid shaft. *These are metric parts with coarse teeth so US spec knobs won't work with the split shaft option Dual MN taper blend-balance with center detent. Split shaft. 17 mm body diameter. " watt, 300 rotation. " shaft diameter. Solder lugs. " bushing. M taper: 0% to 100% output voltage from 0% to 50% rotation (linear). 100% ouput voltage from 50% to 100% rotation. N taper: 100% output voltage from 0% to 50% rotation. 100% to 0% ouput voltage from 50% to 100% rotation (linear). Full output for both outputs at 50% rotation (center detent). Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging

    €13.75