Browse categories ▾

Assembled Resol VBus Board Home Assistant / ESPHome

Assembled Resol VBus Board  Home Assistant / ESPHome
Asking price: €28
Make an offer:
Seller:
Jdsour
Feedback:
Location:
2 more ads from this seller
Entered/Renewed:
2 weeks ago
Ad Views:
328
Viewing 1 of 4
Assembled Resol VBus Board Home Assistant / ESPHome

Description

Condition: New

Assembled Resol VBus-to-UART interface board — reads your Resol / DeltaSol solar thermal controller into Home Assistant via ESPHome.

Wire it to the VBus terminals on your controller and to an ESP32, and pull up to four temperature sensors, two pump-speed channels, operating hours and heat quantity straight into Home Assistant.

Note: heat-quantity readings need the controller's flow/return sensor fitted — without it, that value reads 0.

What you get:

Fully assembled board (SMD parts fitted by JLCPCB, not hand-soldered)
Header pins included, ready to solder — free soldering on request, just ask before buying
A tested, ready-to-use ESPHome config for the DeltaSol BS/2 HE (and rebadges like Joule)

You supply: an ESP32 (or similar) + a few jumper wires. The board runs off the ESP's 3.3V.

Compatibility: reads any Resol / DeltaSol VBus controller — also sold under other names such as Viessmann/Vitosolic, Sonnenkraft and Kingspan. Many DeltaSol models (BS Plus, BS/2, C, CS2, CS4, CS Plus) are natively supported in ESPHome — just select the model. Other models are read by the board and set up with a short custom config. Not sure about yours? Message me your controller model before buying and I'll check.

Based on the open-source FatBeard VBus design. Sold as a hobbyist board, no warranty.

Post anywhere in Ireland for €4.50, or collect in Dublin.

Shipping: CollectionPost/CourierTo be arranged
Payment: CashPaypalTo be arranged
From sellers around the web:
Comments & Offers
Abloggs 1 month ago
Hi. Im looking for temp logging and control of my viessmann vitodens w100 system boiler.
Jdsour 1 month ago
@Abloggs
Thanks for the message! Afraid my board won't suit the Vitodens 100-W — it reads the Resol VBus signal used by Resol/DeltaSol solar controllers (and the Viessmann Vitosolic solar unit, which is a rebadged Resol). Your Vitodens is a gas boiler and doesn't have a VBus output — Viessmann boilers use their own Optolink interface. My board also only logs data; it doesn't control the system.
For getting a Vitodens into Home Assistant, two routes people use:
Viessmann ViCare — the official Home Assistant integration. You'd need a Viessmann Vitoconnect gateway fitted; it then gives you temperatures and some control (hot-water temp, modes) through Viessmann's cloud. Easiest option.
Optolink (DIY) — an optical read-head on the boiler's Optolink port wired to an ESP32; local, no cloud, but more of a project and mainly for logging.
I'd start by searching "Home Assistant ViCare" and "Viessmann Optolink Home Assistant" — there's a big community thread on both.
Best of luck with it — and if you ever add a Resol solar controller, give me a shout!
Cheers
Abloggs 1 month ago
Thanks for the detailed answer. Was looking at home assistant but will checkout homeconnect aswell.
Abloggs 1 month ago
Meant home assistant and optilink. Tnx for the tip!
Jdsour 1 month ago
@Abloggs no worries, best of luck
sondrekol 3 weeks ago
Hi! Do you ship to Norway?
Jdsour 3 weeks ago
@sondrekol yes, but it would be better if you order through my ebay listing https://ebay.io/m/yG7zLB

See more in our Smart Home category available today

€60.00
€80.00
€150.00
€1,000.00
€70.00
€10.00
€20.00
€60.00
€80.00
€100.00
€20.00
€20.00
€100.00
 
€10.00