3 Buy direct from our website through the following link>> https://www.eastwestguitars.com/product/quilter-labs-interbass/ Todays bass player faces new challenges, ranging from performing on silent stages to trying to get a good recording at home without bothering the neighbors. The INTERBASS from Quilter Labs is loaded with powerful features for going direct to PA and recording consoles, combined with a potent little power amp for driving speakers with enough volume for practice and small gigs. Combines the best features of the Bass Block signal path with Quilters latest direct-out connectivity setup. The pedal-sized INTERBASS combines the unmatched dynamic processing of the Bass Block preamp with a 3-band EQ section, active Effects Loop, switchable Cab Sim, and selectable Headphone/Line driver. Active/Passive switch optimizes input level, multiband EQ provides powerful tone shaping, exclusive full flow dynamic processing maximizes headroom, and FR/VINT switch selects modern full-range bass response or a mellower old school tone. Complete with universal 24V power supply and AC cord (Choice of UK or EU plug). SPECIFICATIONS Power: 45 Watts 4 Ohms: 33 Watts 8 Ohms: 17 Watts 16 Ohms Power Requirements: 24 Volt Power Supply (Included) Weight: 0.65 Pounds (0.3 kg) Dimensions: H 5 (12.7cm) x W 4 (10.16cm) x D 1.75 (4.45cm) Outer carton: 10.75 (27.3cm) x 6.25 (15.86cm) x 2.5 (6.35cm) Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Item must be returned in an un-damaged, unblemished state and with all the original packaging.

3 Buy direct from us https://www.eastwestguitars.com/product/precision-bass-harness/ *Please allow up to three working days between build time and postage. Precision Bass Pre-Wired Harness Replacement wiring harness for Fender USA instruments, drop in upgrade for Fender Mexico basses, Squier and Affinity and Fender Mustang bass. Will also fit any bass based on the Fender design. The pots and jack are imperial sized parts so you will need to widen metric sized holes slightly. Specifications: TAD Custom CTS 250k Solid Shaft w/.250" Shaft Potentiometers (Matched pair) Switchcraft 1/4" Mono Input Jack (Soldered connections to the input jack are insulated with heat-shrink to ensure durability and long life) 0.047uf K42Y-2 Paper in Oil Capacitor 22 AWG vintage push-back wire, 18 AWG Buss Wire Solderless connectors available upon request **If you require a left handed harness please nominate before purchase. A left handed harness is 5 extra. The left handed model uses split shaft pots but are supplied with brass adapters for knobs with set screws. Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage by registered mail. Postage on this item is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging.

3 Buy direct from us https://www.eastwestguitars.com/product/jazz-bass-pre-wired-harness-v-treb/ *Please allow up to three working days between build time and postage. Direct replacement harness for Fender USA Jazz bass from 1962 onwards. Drop-in upgrade for Mexican JB's, Squier and similar models. Will also work with Fender Deluxe PJ Bass. Specifications: 250K TAD Custom CTS Solid Shaft Potentiometers w/ (3/8") .375" Shaft Potentiometers, Tolerance 8% (Matched) 2x PMT V-Treb variable treble circuit ***Please note that due to the limited nature and rarity of the Soviet era K40Y-9 capacitors that are pictured here I have to now issue my wiring kits with Orange Drop capacitors. You will receive a 400V Orange Drop 0.047uF capacitor with this kit***. Switchcraft 1/4" Mono Input Jack (Soldered connections to the input jack are insulated with heat-shrink to ensure durability and long life) Professionally soldered using 22 AWG vintage push-back wire and 18 AWG Buss Wire *Control knobs not included The all new V-Treb variable treble bleed/bypass circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. Turning the trim pot 1/4 turn clockwise increases the amount of treble bypass for a brighter sound at reduced volumes. Turning the trim pot 1/4 turn counter clockwise reduces the amount of treble bypass for a warmer tone at reduced volumes. With the volume at 10, the V-Treb is removed from the circuit and does not affect the sound. Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage by registered mail. Postage on this item is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging.

3 Buy direct from us https://www.eastwestguitars.com/product/jazz-bass-harness/ *Please allow up to three working days between build time and postage. Direct replacement harness for Fender USA Jazz bass from 1962 onwards. Drop-in upgrade for Mexican JB's, Squier and similar models. Will also work with Fender Deluxe PJ Bass. Specifications: 250K TAD Custom CTS Solid Shaft Potentiometers w/ (3/8") .375" Shaft Potentiometers, Tolerance 8% (Matched) ***Please note that due to the limited nature and rarity of the Soviet era K40Y-9 capacitors that are pictured here I have to now issue my wiring kits with Orange Drop capacitors. You will receive a 400V Orange Drop 0.047uF capacitor with this kit***. Switchcraft 1/4" Mono Input Jack (Soldered connections to the input jack are insulated with heat-shrink to ensure durability and long life) Professionally soldered using 22 AWG vintage push-back wire and 18 AWG Buss Wire **If you require a left handed harness please nominate after purchase. The left handed model uses split shaft pots but are supplied with brass adapters for knobs with set screws. *Harness is sold without treble bleeds pictured. If you require them please let me know and I can included a pair for 8 extra. Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage by registered mail. Postage on this item is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging.

3 Buy direct from my website at the following link: https://www.eastwestguitars.com/product/mojotone-classic-p-bass-pickup/ Mojotone Classic P-Bass Pickup Description: DCR: 11K (RWRP) Magnet: Alnico 5 Lead: Cloth Push-Back Potted: Yes Output: 6 Bass: 6 Mids: 7 Treble: 7.5 Product Details: Mojotone Classic P-Bass pickup brings excellent clarity with bigger mids as compared to our Clone Series CBS Era P-Bass pickups. Based on the original 1957 'Split-Coil' humbucking pickup they are built stock with Alnico 5 magnets, black fiber bobbins, and vintage spec heavy formvar wire. Hum-cancelling as always and wound to vintage specs. Black pickup covers and mounting hardware included. Vacuum potted coils. Handwound in Burgaw, North Carolina, USA Demos: https://www.youtube.com/watch?v=9ss2tSE5d5U https://www.youtube.com/watch?v=XF-WyxG9uLg Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging Shipping: I offer a choice between Standard or Registered shipping on all my items. I suggest to choose registered mail for your own protection of items being shipped otherwise use standard mail but at your own risk, choose the standard rate if you would like to save on shipping cost. But please be sure that mail never goes missing.

3 The JBX is a jazz pickup with a difference. It has eight hard nickel pole pieces in a stressed field ceramic magnet base for extra power and definition. Adjustable pole pieces. DC Resistance: Bridge: 6.3K Neck: 6K Choice of bridge or neck pickup The pickup is unboxed and supplied with mounting screws and springs. If you require a set buy two items. If you require a plastic display box they are available for 3.00 extra Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Postage is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging.

3 Bass players demand consistency, durability and versatility from their strings. Dunlop delivers. Dunlop Bass Strings offer traditionalists, slappers, and pick-wielding rockers cutting midrange, wide bottom end and a growl that will cut through any band. Carefully selected core to wrap ratios yield a low tension string with an extremely long life, and minimal break-in time. Each set is exceptionally well balanced string to string, and provides an amazing amount of dynamic range. Gauges: 45-65-85-105-130