Browse categories

East-West Guitars 

Quality Replacement Parts

Member since:
17/04/2015
Last online:
21/05/2019
Location:
Rathfarnham, Dublin

Activity

Active:
197
Sold out:
31
Withdrawn:
96
Units sold:
925

Feedback Score [309]

  • CTS Push-Pull (DPDT) Potentiometer, Choice of 250K or 500K, Split Shaft

    3 The best push-pull potentiometer on the market! Custom made with the smoothest taper possible and the tightest tolerance available. Use for coil tapping, series parallel switching and phase reverse. Wire your guitar in new and imaginative ways. -Choice of 250K or 500K -Split Shaft -Shaft Diameter: 3/8'' (9.40mm) -Thread: 3/8'' x 32 -Shaft Height: 3/8'' (9.80mm) -Required Mounting Hole: +3/8'' (9.5mm) -Reuired cavity depth - 28mm minimum -Taper Resistance: 15% -Tolerance: +-7% Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Postage on this item is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Purchase with confidence that the excess cost of postage which seems to add up here in Adverts shopping cart when buying multiple items is refunded immediately after transaction.

    €11.95
  • CTS Push-Pull (DPDT) Potentiometer, 500K Long Shaft

    3 For deep control cavities such as Gibson Les Paul guitars. The best push-pull potentiometer on the market! Custom made with the smoothest taper possible and the tightest tolerance available. Use for coil tapping, series parallel switching and phase reverse. Wire your guitar in new and imaginative ways. -Choice of 250K or 500K -Shaft Diameter: 3/8'' (9.40mm) -Thread: 3/8'' x 32 -Shaft Height: 3/4'' (19mm) (Long shaft 3/4'' 500k will be available soon) -Solid brass split shaft and bushing (3/8'' diameter x 3/8'' length) -Required Mounting Hole: +3/8'' (9.5mm) -Taper Resistance: 15% -Tolerance: +-7% Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Purchase with confidence that the excess cost of postage which seems to add up here in Adverts shopping cart when buying multiple items is refunded immediately after transaction.

    €12.95
  • CTS Push-Pull (DPDT) Potentiometer, Choice of 250K or 500K, Solid Shaft

    3 The best push-pull potentiometer on the market! Custom made with the smoothest taper possible and the tightest tolerance available. Use for coil tapping, series parallel switching and phase reverse. Wire your guitar in new and imaginative ways. -Choice of 250K or 500K -Solid Shaft -Shaft Diameter: 3/8'' (9.40mm) -Thread: 3/8'' x 32 -Shaft Height: 3/8'' (9.80mm) -Solid brass shaft and bushing (3/8'' diameter x 3/8'' length) -Required Mounting Hole: +3/8'' (9.5mm) -Reuired cavity depth - 28mm minimum -Taper Resistance: 15% -Tolerance: +-7% Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Postage on this item is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Purchase with confidence that the excess cost of postage which seems to add up here in Adverts shopping cart when buying multiple items is refunded immediately after transaction.

    €13.95
  • Quilter Labs Interblock 45, Pedal Sized Amplifier

    3 ON THE STAGE | IN THE STUDIO | IN YOUR RIG ON THE STAGE: Powerful: The InterBlock 45 delivers up to 45 watts power for your cabinet. Enough power to give your pedals, your modeler, or anything that needs to be heard enough power and life for a serious gig. Silent: Find yourself on a stage where amps are not allowed? Don't sacrifice tone! Plug in your InterBlock 45, and select the Balanced Line Output, then choose FR or cab sim to give your PA the same luscious life and tone that you give your speakers. IN THE STUDIO: Versatile: Available FR or Cab simulated mode to coax the most life out of your instrument and into your DAW. Extensible: Love your outboard effects pedals and want them warmed up before the recording? Put them in the onboard FX loop and add your sound to your recordings. Rig Integration: This is the answer when you need to power your modeling rig. Switch from Cab Sim to FR mode for stiff output that gets the most from your modeling speaker sim. Pedal power: With up to 45 watts onboard power and an FX loop, the InterBlock 45 integrates perfectly with your pedalboard turning your pedalboard into a go anywhere, do anything, unstoppable force of nature. Specifications: 45 Watts 4 Ohms: 33 Watts 8 Ohms: 17 Watts 16 Ohms 0.65 Pounds (0.3 kg) 24 Volt Power Supply (Included) H 5 (12.7cm) x W 4 (10.16cm) x D 1.75 (4.45cm) Outer carton: 10.75 (27.3cm) x 6.25 (15.86cm) x 2.5 (6.35cm) Manual: https://www.quilterlabs.com/manuals/Quilter-InterBlock45-Manual.pdf Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Quilter Labs Warranty Information: Customers may have additional rights, which vary from state to state or from country to country. In the event that a provision of this limited warranty is void, prohibited or superseded by local laws, the remaining provisions shall remain in effect. The Quilter Labs limited warranty is valid for a period of three (3) years from date of purchase except that footswitches, covers, cabinets, handles, and cabinet hardware are warranted for a period of one (1) year and speakers, and all other included accessory products for a period of ninety (90) days from date of purchase. All accessories (Footswitches, controllers, deluxe cases) are warranted for a period of 90 days from date of purchase. Defective products that qualify for coverage under this warranty will be repaired or replaced, (at Quilter Labs' discretion) with a like or comparable product, without charge. To receive warranty service, return the complete product to Quilter Labs, LLC, with proof of purchase, during the applicable warranty period. The Quilter Labs Dealer from whom you purchased your product may also be authorized for warranty service and should be the first point of contact when service is required. TRANSPORTATION COSTS ARE NOT INCLUDED IN THIS LIMITED WARRANTY. Any repair or service performed by any person or entity other than an Authorized Quilter Labs Electronics Service Center is not covered by this limited warranty.

    Guitar Amps
    2 months ago 0 comments
    €235
  • Marshall JCM2000, TSL 100 Amplifier Head

    3 Recently serviced here at East-West Guitars and fitted with a set of JJ Electronics power tubes specially matched by Apex Engineering https://www.apexmatching.com/how-apex-matching-works This head has the upgraded turquoise power board which solved the thermal drift issue which the first models suffered from. Beautiful clean amp, tolex in mint condition. Biased and road ready. Footswitch controller and power cable included Features: Three independent channels with separate EQ, volume and gain, and master controls for reverb, presence, FX mix, and deep switch Clean channel mid boost switch which bypasses middle pot and reconfigures the way the treble and bass controls work together Two effects loops with level control Emulated Line Out Power Reduction (Reduces power output to 25W) Selectable parallel 4 and 8 Ohm speaker outputs and standalone 16 Ohm output Output Mute switches (Great for changing guitars on stage without hitting standby switch) Five-button footswitch with LEDs for channel selecting, reverb, and FX loop Open to offers, not swaps. If purchasing from UK and EU countries please inquire about shipping prices as I will need to get a quote for a courier first. Price of shipping will then be added to sale price.

    Guitar Amps
    2 months ago 0 comments
    €550
  • Dr. Duck's Ax Wax & String Lube, Organic, Made in USA

    3 Dr. Duck's Ax Wax & String Lube For use on the entire fretboard, headstock, front,sides, back and pickguards. Also cleans and lubes bridge saddles, fine tuners on locking tremolo systems, tuning machine knobs and posts. US made with US materials, 4 oz. Just one drop of this stuff will do a whole guitar so one bottle will last you a long, long time if used sparingly! RoHS Compliant Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Postage is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging.

    €9.95
  • Stomp Box Footswitch 3PDT (True Bypass)

    3 High quality stompbox footswitch. Use as an economical replacement or for wiring pedals for true bypass. A good alternative switch to Dunlop for Crybaby Wah-Wah. Allows wiring an LED 3PDT (Triple Pole, Double Throw) Latching type footswitch. Includes 2 hex nuts, a vibration proof washer and a nylon washer. Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Combined postage on all listings in my shop is available from East-West Guitars although Adverts does not seem to have this function unlike Ebay. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately**

    €6.95
  • Entwistle XS 62N Stratocaster Pickup (Bridge/Middle/Neck)

    3 UK guitar designer and pickup guru Alan Entwistle has over 30 years of research and experience of hand making custom pickups. His CV includes heading up Hohners UK based Custom Shop where he designed models including the JT60, Blond, Black Widow and Revelation. More recently he has designed guitars for Alden and Tanglewood and his electronic circuit wizardry is being incorporated into selected Burns models. The XS 62N is Entwistle's most powerful single coil pickup. Using 6 hard nickel poles and neodymium magnets the XS62N has been given HDN (High Definition Neodymium) technology for great definition and very high output whilst still rendering those treasured single coil tones. Available for Bridge, Middle & Neck. Adjustable pole pieces. *Available with choice of pickup covers, White, Black or Cream DC Resistance: Bridge: 9.5K Middle: 7.5K Neck: 7K The pickup is unboxed and supplied with mounting screws and springs. Choice of Bridge Middle or Neck Pickups If you require a set buy three items. If you require a plastic display box they are available for 3.00 extra Demos: https://www.youtube.com/watch?v=UfaVAULcQUg https://www.youtube.com/watch?v=lEw092-oDVo

    €14.95
  • Entwistle AS57 Alnico Single Coil Pickup (Bridge/Middle/Neck)

    3 UK guitar designer and pickup guru Alan Entwistle has over 30 years of research and experience of hand making custom pickups. His CV includes heading up Hohners UK based Custom Shop where he designed models including the JT60, Blond, Black Widow and Revelation. More recently he has designed guitars for Alden and Tanglewood and his electronic circuit wizardry is being incorporated into selected Burns models. The AS57 is a traditional vintage alnico single coil with sparkling highs, warm mids and a well defined low end. Traditional materials are used with AlNiCo pole pieces, fibre board bobbin and enamel coated winding wire which is scatter-wound direct to the core. This attention to materials and construction detail ensures authentic vintage tone. The middle pickup is reverse wound so that hum is cancelled when used in combination with either the neck or bridge pickups. DC Resistance: Bridge: 6.5K Middle: 6.5K Neck: 6.5K *Available with choice of pickup covers, White, Black or Cream The pickup is unboxed and supplied with mounting screws and springs. Choice of Bridge Middle or Neck Pickups If you require a set buy three items. If you require a plastic display box they are available for 3.00 extra

    €19.95
  • Vintage Top Hat Knobs, Chrome Foil Topped (2 tone/2 volume) 2 colours/styles

    3 Set of four retro styled potentiometer knobs for Gibson SG, Firebird etc. Can also be sold seperately upon request. Set of four (2 tone/2 volume) Colors: Gold with Gold Foil Top Gold with Silver Foil Top Black with Gold Foil Top Black with Silver Foil Top Fits US spec split shaft potentiometers with fine splines. **If only one pair is required please let me know and I can drop the price accordingly

    €15.80
  • Fender S-1 Potentiometer, Split Shaft, 250K, 0.25B Taper

    3 "Tone up" and modify your favorite guitar or bass with an S-1 Switch from Fender. Originally featured as an upgrade to American and American Deluxe Series guitars and basses in 2003, the S-1 switch allows a multitude of tonal options for your instrument. The S-1 switch features four "stages" and can be wired into a variety of configurations (SPST, DPDT for a coil-tap, or 4PDT for a dual hum bucking coil tap). Works great in conjunction with a 4-pole "Super" Switch. 250K split shaft design. Accepts push-on mounting knobs only. Switch knob and tip are also available in my shop. Made by CTS Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packagingShipping: I offer a choice between Standard or Registered shipping on all my items. I suggest to choose registered mail for your own protection of items being shipped otherwise use standard mail but at your own risk, choose the standard rate if you would like to save on shipping cost. But please be sure that mail never goes missing.

    €28.95
  • Fender TBX Tone Control

    3 250K/1 Meg Ohm stacked and detented potentiometer. Original TBX tone control for most Strats and Teles. CTS manufactured, includes capacitor and comes in original Fender packaging. Some instruments have a unique tone circuit that features a TBX Tone Control (Patented). The TBX (which stands for Treble Bass Expander), is a dual concentric stacked tone pot. The pot has a detent in the middle position. From 0 to 5 (at the detent), the TBX functions like a normal tone circuit with filtration through a capacitor. Advancing the knob counterclockwise from the detent position gradually filters off high frequencies, like a standard tone control. Rotate the knob clockwise from the detent position, and you add presence and brightness by allowing the pickups' natural resonance to come through. UPC/EAN: 717669448011

    €15.95
  • V-Treb Variable Treble Bleed Circuit, Precision Music Technologies

    3 The V-Treb variable treble bleed/bypass circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. With the volume at 10, the V-Treb is removed from the circuit and does not affect the sound. To lnstall: 1. Peal the adhesive tape backing and attach the V-Treb circuit to the back of the volume pot as shown or chose another location to mount the circuit to allow easy adjustment if the back of the volume pot can not be accessed for adjustment. 2. Solder the input and output terminals of the volume pot to the gold solder pads on the bottom of the V-Treb or run wires as shown if mounted remotely from the volume pot. 3.Connect original input and output wires from volume to the gold solder pads on the top of the V-Treb or pot as shown. To Adjust The V-Treb: Set the volume between 6 and 8. Then use a small screwdriver to adjust the orange bypass amount control to the desired amount of treble bypass. Turning the trim pot clockwise increases the amount of treble bypass for a brighter sound at reduced volumes. Turning the trim pot counter clockwise reduces the amount of treble bypass for a warmer tone at reduced volumes. The V-Treb will not affect the tone when the volume pot is set to 10 (100% on) NOTE: Use a small flat head screwdriver and be careful not over turn or damage the trim pot. Get precise adjustment of tone as volume is reduced. Use with 250K & 500K pots - Single coils & Humbuckers. Improves audio taper roll off between 6 and 10. Will not affect tone at full volume. Mounts to any volume pot with included adhesive tape. Can also be remote mounted for easier adjustment. *Volume pot not included. Demo: https://www.youtube.com/watch?v=MYpjezFkIeM

    €12.95
  • Tube Amp Doctor 6V6GT-STR PREMIUM, Matched Vacuum Tubes

    3 *Buy two, you get a matched quartet 6V6GT-STR TAD PREMIUM Matched TAD 6V6GT-STR (aka. 7408 / 6V6GTY) PREMIUM tube Finally in production after 3 years of intensive research. This all new TAD 6V6GT-STR combines the exceptionally sweet characteristics of the NOS 6V6GT by RCA or of the GE 6V6GTY. It is a heavy duty 6V6GT tube, which can handle a higher plate current. This TAD 6V6GT-STR caters for a detailed and powerful tone and an abundance of sustain; characteristics you would only expect from the finest NOS 6V6GTs from the 50s and 60s. Even when pushed into saturation there are no harsh upper mids, which is frequently the case with other 6V6s. Sweet full-bodied tone with silky highs. We recommend the TAD 6V6GT-STR for all 6V6 applications where a powerful but sweet tone is desired; It works great in amps like the Fender -Tweed- Champs, Deluxe Reverb Amps, Vibro-Champ, Fender Champion 600 or the Univalve. This is also the perfect choice as a reverb driver for the Vibrokings and Dual Professionals. Q: When does a power tube become a Premium Selected power tube? A: All power tubes labeled Premium Selected have passed the following tests: -Plate Current (PC) and Amplification (TC) -Low Noise Test -Microphonic Test -Sonic Tests -Shock Tests -Listening Tests -Shorts & Leakage Tests Premium RT-Matching of Power Tubes Our Premium Matching is an exact matching of power tubes with identical Plate Current (PC) and Transconductance (TC). TAD Premium Selected tubes are guaranteed for a period of 6 months (according to terms of warranties) for the quality criteria mentioned above. RohS Compliant Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Must be returned in an un-used state and in the original packaging.

    Guitar Amps
    8 months ago 0 comments
    €50
  • Tube Amp Doctor EL84M (Military Grade) Premium Matched Tubes

    3 *Buy two, you get a matched pair *Buy four, you get a matched quartet EL84M TAD-Tubes, Premium Matched Your 1st Choice When Dependability is Your Major Goal! The TAD EL84M offers strong mids and defined bass response. Even, when played at lower volume or in a complex stage sound situation, your sound will prevail. This is the most reliable and longest-lasting military grade EL84 on the market and operates up to 10,000 hours. Unfortunately, this tube is not being produced anymore. Grab them, while they last! d= 22,5mm Due to its diameter of 22.5mm, the TAD EL84-M does not fit into older Marshall DSL401 and UK made VOX AC15 TBX amplifiers. The only tube which fits these amps is the EL84-EI. (ordering number: NN471) Q: When does a power tube become a Premium Selected power tube? A: All power tubes labeled Premium Selected have passed the following tests: -Plate Current (PC) and Amplification (TC) -Low Noise Test -Microphonic Test -Sonic Tests -Shock Tests -Listening Tests -Shorts & Leakage Tests Premium RT-Matching of Power Tubes Our Premium Matching is an exact matching of power tubes with identical Plate Current (PC) and Transconductance (TC). TAD Premium Selected tubes are guaranteed for a period of 6 months (according to terms of warranties) for the quality criteria mentioned above. RohS Compliant Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Must be returned in an un-used state and in the original packaging.

    Guitar Amps
    8 months ago 2 comments
    €30
  • Tube Amp Doctor ECC83 WA Preamp Tube (Premium Selected)

    3 ECC83 WA TAD Premium Selected Perfect V2 Preamp Tube!! Great Dynamics - Low Noise - Warm Tone!! The TAD ECC83 WA Selected provides a stunning warm tone, thick midrange and sweet natural harmonics. We designed it with a triple mica construction for low noise performance. Perfect for clean or moderate gain preamps as well as for high-gain amps from V2 position (for V1/Input stage the HIGHGRADE selection RT080 is recommended). Its great dynamics, low noise operation and balanced warm tone make the TAD ECC83 WA to be an excellent all-rounder with great value for money. - smooth top end - full gain - fat mid range - tight low end - very low microphony - low noise - balanced systems - triple mica construction - replaces: 12AX7, 12AX7A/WA/WB/WC, ECC83, 7025 The TAD ECC83WA Premium Selection is recommended for most applications for low microphony performance. For especially demanding input stages (V1) and for all applications demanding an extremely low microphony 7025 / ECC83 / 12AX7A type tube we recommend the RT080 TAD 7025WA HIGHGRADE. For "normal" applications the RT008 TAD ECC83 WA Selected can be used with same sound and gain structure. 1st choice tube to improve your: Boogie, Brunetti, Carrl, Diezel, Egnatorl, Engl, Fender, Hughes & Kettner, Koch, Laney, Marshall, Mesa, Orangel, Soldano, Trace Elliot, Two Rockl, VOX uvm. Q: When does a preamp tube become a Premium Selected tube? A: All preamp tubes labeled Premium Selected have passed the following tests: -Low Noise Test -Microphonic Test -Gain Test -Sonic Tests -Shock Tests -Listening Tests -Balanced Output Test TAD Premium Selected/Highgrade tubes are guaranteed for a period of 6 months (according to terms of warranties) for the quality criteria mentioned above. RohS Compliant

    Guitar Amps
    8 months ago 39 comments
    €14.95
  • Pure Tone Mono Output Jack (Nickel)

    3 The patented Pure Tone jack contains dual tension grounds and dual positive tips for optimal signal and lowest possible noise. 100% greater surface area at all contact points creates a more stable connection; as a result, high and low frequencies are greatly improved creating a much more balanced sound while eliminating frequency spikes. No more noise crackle caused by pressure grounds! The Pure Tone jack allows for increased current handling at 500 volts for high current applications. Tensioned design locks cable securely in place while the increased metal mass carries more signal. US Patent 9,680,264 Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Must be returned in an un-used state and in the original packaging

    €5.95
  • Switch Washer, Rhythm/Treble, Gold Lettering, for LP, SG etc

    3 This Rhythm - Treble Ring for Gibson Les Paul is on thin plastic with Gold Lettering. The self-adhesive backing makes it easy to apply under the washer and nut of your typical 3-way toggle switch. Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. All items must be returned in an unused state and in the original packaging.

    €3.95
  • Telecaster Wiring Harness with 4-way Switch Modification

    3 ***Reverse control harness available upon request for same price*** Fender Telecaster pre-wired control harness with 4-way switch mod. Position 2 of the 3-way Telecaster selector switch gives you both pickups wired in parallel; this is a standard wiring, and one of the classic Telecaster tones. But what if you need a fatter sound out of your Tele? The two outside switch positions on the Tele - which select the bridge or neck pickup individually - stay basically the same. But the middle position (both pickups together) wires the pickups in series rather than parallel. This produces a thicker, meatier sound, while still retaining the recognizable characteristics of a Tele. This is not a hum-cancelling combination, but it gives the increased power of a series link. The 4-way Tele switch will give you both sounds when you dial in the two pickups together - wired in parallel (standard wiring) and wired in series for a beefier fuller sound. **Can be supplied with crimp connectors for solderless hook up if required** Kit includes: Emerson PRO CTS Solid Shaft (audio taper/logarithmic) potentiometers (Matched) Oak Grigsby 4-Way Switch Switchcraft 1/4" Mono Input Jack with pre-wired harness using shielded braided wire enclosed with heat shrink tubing and also used on connections for strength (not pictured, see 3-way harness for better idea on location) Soviet Union NOS 0.047uf/47nF K42Y-2 Paper in Oil Capacitor (Tested within the 10% range) Choice of 50's Wiring (pictured) or Emerson Treble Bleed/Volume Mod Professionally soldered using vintage push-back wire. Switch Positions: 1. Bridge 2. Bridge & Neck in Parallel 3. Neck 4. Bridge & Neck in Series (Humbucker Type Fullness) **Switch Tip and Control Knobs Not Included** Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Postage is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging.

    €65
  • Fender Telecaster 3-Way Wiring Kit (50's Wiring Modification)

    3 ***Standard and Reverse control harness available upon request for same price*** (Standard Tele harness is supplied with an Emerson Treble Bleed/Volume Mod). Left-handed kits are 5 extra, please inquire first before purchase if you require this. Fender Telecaster pre-wired control harness with 50's Les Paul wiring modification. Two simple solder connections required. Drop in upgrade for Squire and Affinity Tele's. **Can be supplied with crimp connectors for solderless hook up if required** Kit includes: Emerson PRO CTS Solid Shaft (audio taper/logarithmic) potentiometers (Matched) Oak Grigsby 3-Way Switch Switchcraft 1/4" Mono Input Jack with pre-wired harness using twisted vintage push back wire enclosed with heat shrink tubing and also used on connections for strength Soviet Union NOS 0.047uf/47nF K42Y-2 Paper in Oil Capacitor (Tested within the 10% range) Professionally soldered using vintage push-back wire. **Switch Tip and Control Knobs Not Included** Whats so special about this 50s wiring? It affects your tone in three major ways: 1. The overall tone gets stronger, tighter, and more transparent. Its difficult to describe, but you might say its more in your face. 2. The typical treble loss that occurs when rolling back the volume is much less than with standard wiring. Both the volume and tone controls become more responsive, and they react more smoothly without the usual hot spots. Another bonus: By simply rolling back your guitar volume a bit, you can clean up an overdriven amp without getting lost in the mix. 3. The tone and the volume controls interact with each othersomething you might be familiar with from certain tweed-era Fender tube amps. When you change the volume, the tone changes a little bit as well, and vice-versa. This may be strange at first, but you only need a few minutes to get used to it. The 50s wiring exhibits much less treble loss that standard wiring because it follows a completely different curve, depending on the ratio of your pot. It works best with audio taper pots, preferably those with a 60:40 or 70:30 ratio. Smaller ratios like 80:20 or 90:10 limit this benefit and result in the typical on/off or bright/dull problem when using the controls. Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Postage on this item is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. .

    €60
  • Phase Reverse/Split Coil Wiring Harness For Gibson Les Paul, Epiphone, Tele Deluxe

    3 Phase Reverse/Split Coil Wiring Harness For Gibson Les Paul, Epiphone, Telecaster Deluxe etc Specifations 2x CTS Push/Pull 500K Potentiometers 2x Emerson Custom 500k Potentiometers 1x K40Y-9 0.022uF (22nF) Paper in oil capacitor 1x K40Y-9 0.015uF (15nF) Paper in oil capacitor Switchcraft J11 Mono Jack Bridge volume control switch splits humbucker coil Neck volume control switch for phase reversal Can be supplied as a solderless harness with quick splice connectors If you require a customised harness please inquire. Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage by registered mail. Postage on this item is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging.

    €85