3 Fits standard 1/4" USA solid shaft pots CTS etc. Finish (Chrome) Uses a flat head set screw for tightening on to the pot shaft

3 Buy direct from my website: https://www.eastwestguitars.com/product/wilkinson-compensated-saddles-brass-for-telecaster/ These saddles made by Wilkinson allow you to have more control over intonation and still keep that classic Tele appearance. Made from machined brass saddles utilising a staggered design pattern. Will work with any 'Ashtray' style Telecaster style bridge Made as a saddle replacement for Wilkinson B-WTB bridges 3 saddles per pack Feel free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase, you can return it to us within 14 days, and a full refund will be provided. Buyer assumes responsibility for return postage. Item must be returned in an unused state and in original packaging.

3 Buy direct from us https://www.eastwestguitars.com/product/les-paul-standard-harness/ *Please allow up to three working days between build time and postage. *Modern Wiring harness pictured* By default the harness will be wired vintage 50's. If you prefer modern wiring let me know and I'll build it to your request at no extra cost. This harness is for Les Paul models with a flat top body instead of the curved arch top models. These normally utilise short shaft potentiometers and that is reflected in this pre-wired harness. Will work in any Epiphone Les Paul Studio and other styled copies for a welcome upgrade to quality components. Specifications: Kit includes: Tube Amp Doctor PRO CTS 500K Split Shaft (audio taper/logarithmic) Short potentiometers (Matched) 30% log taper, 3/8" bushing Switchcraft 1/4" Mono Input Jack Soviet Union NOS 0.022uF/22nF and 0.015uF/15nF K40Y-9 Paper in Oil Capacitors and (Tested within the 10% range) The 15nF takes some off the mud of the neck 18 AWG Buss Wire **Switch Tip and Control Knobs Not Included** If you require long 3/4" pots for Gibson LP's, message me and I'll change the price. Long version is 4 extra. Whats so special about this 50s wiring? It affects your tone in three major ways: 1. The overall tone gets stronger, tighter, and more transparent. Its difficult to describe, but you might say its more in your face. 2. The typical treble loss that occurs when rolling back the volume is much less than with standard wiring. Both the volume and tone controls become more responsive, and they react more smoothly without the usual hot spots. Another bonus: By simply rolling back your guitar volume a bit, you can clean up an overdriven amp without getting lost in the mix. 3. The tone and the volume controls interact with each othersomething you might be familiar with from certain tweed-era Fender tube amps. When you change the volume, the tone changes a little bit as well, and vice-versa. This may be strange at first, but you only need a few minutes to get used to it. The 50s wiring exhibits much less treble loss that standard wiring because it follows a completely different curve, depending on the ratio of your pot. It works best with audio taper pots, preferably those with a 60:40 or 70:30 ratio. Smaller ratios like 80:20 or 90:10 limit this benefit and result in the typical on/off or bright/dull problem when using the controls. Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage by registered mail. Postage on this item is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging.

3 Buy direct from us https://www.eastwestguitars.com/product/tele-harness-4-way-switch-mod/ *Reverse control harness available upon request for extra 5*** *Please allow up to three working days between build time and postage. Fender Telecaster pre-wired control harness with 4-way switch mod. Position 2 of the 3-way Telecaster selector switch gives you both pickups wired in parallel; this is a standard wiring, and one of the classic Telecaster tones. But what if you need a fatter sound out of your Tele? The two outside switch positions on the Tele - which select the bridge or neck pickup individually - stay basically the same. But the middle position (both pickups together) wires the pickups in series rather than parallel. This produces a thicker, meatier sound, while still retaining the recognizable characteristics of a Tele. This is not a hum-cancelling combination, but it gives the increased power of a series link. The 4-way Tele switch will give you both sounds when you dial in the two pickups together - wired in parallel (standard wiring) and wired in series for a beefier fuller sound. **Can be supplied with crimp connectors for solderless hook up if required** Be aware though that the metal cover on the neck pickup needs to be grounded separately for the series option to work, which will require disconnecting the jumper wire and soldering a cable to it. Kit includes: Emerson PRO CTS Solid Shaft (audio taper/logarithmic) potentiometers (Matched) Oak Grigsby 4-Way Switch Switchcraft 1/4" Mono Input Jack with pre-wired harness using shielded braided wire enclosed with heat shrink tubing and also used on connections for strength (not pictured, see 3-way harness for better idea on location) Soviet Union NOS 0.047uf/47nF K42Y-2 Paper in Oil Capacitor (Tested within the 10% range) Choice of 50's Wiring (pictured) or EWG Treble Bleed/Volume Mod. Harness is 50's wiring by default. Professionally soldered using vintage push-back wire. Switch Positions: 1. Bridge 2. Bridge & Neck in Parallel 3. Neck 4. Bridge & Neck in Series (Humbucker Type Fullness) **Switch Tip and Control Knobs Not Included** Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Postage is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging.

3 Buy direct from us https://www.eastwestguitars.com/product/prs-2-control-wiring-harness/ *Please allow up to three working days between build time and postage. For PRS and PRS SE guitars with a two control layout and three way toggle switchswitch. Choice of split or solid shaft pots. Split shaft by default *Left hand harness available for an extra 5. 500K Emerson PRO Split Shaft w/.375" (3/8") Shaft Length (audio taper/logarithmic) potentiometers Right angled Switchcraft pickup selector switch Deep knurled nut for switch NOS K40Y-9 0.022uF paper in oil capacitor. Switchcraft J11 output jack Wired with vintage shielded braided cable *Can be built for solderless connections if required Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage by registered mail. Postage on this item is at the standard rate, if you want your items sent by registered post please send me a message. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging.

3 Mojotone '52 Clone Tele Pickup DESCRIPTION Neck: 5.9K Magnet: Alnico 3 Cover: Chrome Output: 4.5 Bass: 3 Mids: 3.5 Treble: 6 Bridge: 6.5K Magnet: Alnico 3 Output: 5 Bass: 4 Mids: 4.5 Treble: 5.5 Product Details All original manufacturing methods are the same with handwound coils, and wax potted coils. RWRP when combined for hum-cancelling in the middle position. We voiced these around the best examples we encountered from the blackguard era. The neck pickup is so clear and soft with lots of articulation. The bridge pickup has just the right amount of mids with clear wide open twang and snap. These pickups really let you dial your amp in for the best possible tone. Handwound in Burgaw, North Carolina, USA Demos: https://www.youtube.com/watch?v=KhWMPapjVA0 https://www.youtube.com/watch?v=WgqwWtkoMG4 Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging Shipping: I offer a choice between Standard or Registered shipping on all my items. I suggest to choose registered mail for your own protection of items being shipped otherwise use standard mail but at your own risk, choose the standard rate if you would like to save on shipping cost. But please be sure that mail never goes missing.

3 This pot will allow you to wire your guitar up the correct way if you are a left handed player. Potentiometers on left handed guitars usually can only be operated in an anti-clockwise fashion which is a nightmare for some players or with a reverse wiring with a standard pot with the wires simply reversed which is not correct at all as it will reverse the resistance taper. This pot is the answer and will allow the player to engage the control in a clockwise manner when turning it up. From Allparts USA Specifications: Resistance: 250k Ohms Tolerance: +/-10% Shaft Material:Aluminum Pot casing: Dimpled back Shaft Style: (24 Spline) Split Shaft, Fine Knurling Shaft Diameter: 0.234 (6.00MM) Shaft Height: 1/4 (6.4MM) Thread: 3/8 X 32 Thread Height: 1/4 (6.4MM) Required Mounting Hole: 3/8 (9.52MM) ***THESE ARE NOT METRIC COMPONENTS, SOME REAMING OF THE RECIEVING HOLES MAY BE NEEDED! ALSO, THE KNOBS ON YOUR GUITAR MAY NEED TO BE REPLACED AS THESE POTS ARE THE FINE SPLINED VARIETY AS OPPOSED TO THE COURSE SPLINES ON EUROPEAN GUITARS*** Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Potentiometers and other electronic soldered components must be returned in an un-used, un-soldered state and in the original packaging. **Combined postage on all listings in my shop is available from East-West Guitars. However, until Adverts get around to offering the customer and the seller a shopping cart so the seller can calculate the shipping for the customer for multiple items the only solution is as follows. If you are purchasing a bundle of different items I will refund you the surplus cost of postage or shipping immediately**

3 High Quality 'Ashtray' style bridge for Tele styled guitars made by Boston Musical Products. Six individual vintage styled saddles allows complete intonation over each string. Dual mounting system allows bridge mounting of strings or through the body Screws and hex wrench for saddle height adjustment included Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Must be returned in an unused state and in the original packaging

3 High Quality 'Ashtray' style bridge for Tele styled guitars made by Boston Musical Products. Six individual vintage styled saddles allows complete intonation over each string. Dual mounting system allows bridge mounting of strings or through the body Screws and hex wrench for saddle height adjustment included Matt Black Finish Feel Free to ask any questions Terms and conditions: If for any reason you are not 100% satisfied with your purchase you can return it to us within 14 days and a full refund will be provided. Buyer assumes responsibility for return postage. Must be returned in an unused state and in the original packaging

3 Give your control knobs some vintage aesthetic with some pointer washers 90 angle on point (Gold or Nickel) Sold per unit 3/8" hole diameter for US spec pots CTS etc Part #: KLP-1800N/G Please make sure to indicate which finish and angel you require.

3 *Please state if you want Slotted or Unslotted when ordering. The Zero Glide Replacement Nut System borrows the zero fret concept to reduce string contact in the nut by up to 93%, increasing tuning stability, playability, and open string tone. It only take a few minutes to install with absolutely no permanent alteration to your instrument Specifications: TOTAL LENGTH45.8mm (1 51/64) STRING SPACING (OUTSIDE STRINGS)36.5mm (1 7/16) END HEIGHT8.64mm (11/32) MIDDLE HEIGHT9.5mm (3/8) FINGERBOARD HEIGHT (MAX)7.3mm (9/32) WIDTH5.9mm (15/64) RADIUS(12) *This radius will fit +/- 2 radius on your instrument as the fret will self seat to your fingerboard radius. INCLUDED FRETS (HEIGHT/COLOR)Low 0.035 / red code Medium 0.039 / purple code High 0.043 / blue code Jumbo 0.051 / no color code STRING SIZE (MAX).013 .056 Demos: https://www.youtube.com/watch?v=y_xo4yA7TJI Installation: https://www.youtube.com/watch?v=i-VuukWD3Jw Review: https://www.youtube.com/watch?v=9O4nh4IP7eU